FMVSS 208 REGULATION PDFFMVSS 208 REGULATION PDF

Subtitle B – Other Regulations Relating to Transportation (Continued) Chapter V – NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION. (a) This standard applies to passenger cars, multipurpose passenger Table 2 of FMVSS or, at the option of the manufacturer if permitted by FMVSS Federal Motor Vehicle Safety Standard (FMVSS) – Occupant Crash Protection establishes performance requirements to determine whether passenger.

Author: Dairr Faulmaran
Country: China
Language: English (Spanish)
Genre: Politics
Published (Last): 6 July 2008
Pages: 276
PDF File Size: 3.66 Mb
ePub File Size: 19.10 Mb
ISBN: 935-6-18887-485-4
Downloads: 70392
Price: Free* [*Free Regsitration Required]
Uploader: Shaktizahn

Using any part of any controlother than those just used, determine the full range of angles of the seat cushion reference line and set the seat cushion reference line to the middle of the range. A The request must provide a mock-up of the label with the specific language or pictogram the fmcss requests permission to add to the label.

Effective April 27, Push rearward on the dummy’s knees to force the pelvis into the seat so there is no gap between the pelvis and the seat back or until contact occurs between the back of the dummy’s calves and the front of the seat cushion.

Using any part of any control other than those that primarily move the seat or seat rwgulation fore and aft, while maintaining the seat cushion reference line angle, place the SCRP to its lowest position. Thompson did not provide persuasive quantitative data to show adopting his requested changes would result in a net benefit to safety.

If a seat belt assembly installed in compliance 2208 this requirement includes an automatic locking retractor for the lap belt portion, that seat belt assembly shall comply with paragraphs a through c of S4. After consideration of the petitions and all supporting information, NHTSA has decided to grant the petitions for four of the discrete changes, deny one, and request comment in a separate document for the sixth proposed change.

NHTSA has granted Toyota’s petition and proposes to establish appropriate performance requirements to ensure the safe introduction of adaptive driving beam headlighting systems if equipped on newly manufactured vehicles. Transit bus means a bus that is equipped with a stop-request system sold for public transportation provided by, or on behalf of, a State or local government and that is not an over-the-road bus.

  ASTM E114 PDF

Evenflo Tribute V xxxx or Evenflo Tribute xxxx. At the lower edge of the platform is an unyielding flange, perpendicular to the platform with a height of 4 inches and a length sufficient to hold in place the tires that rest against it. Graco Platinum Cargo September 25, Position the dummy with the spine vertical so that the horizontal distance from the dummy’s back to the seat back is no less than 25 mm 1. This appendix does not apply to vehicles manufactured on or after September 1, Any of the following forward-facing child restraint systemsand forward-facing child restraint systems that also convert to rear-facing, manufactured on or after the date listed, may be used by the National Highway Traffic Safety Administration to test the suppression or LRD system of a vehicle that has been certified as being in compliance with 49 CFR If the dummy contacts the vehicle interior, using only the control that primarily moves the seat fore and aft, move the seat rearward to the next detent that provides clearance.

Each vehicle manufactured on or after September 1,and before September 1,shall meet the requirements specified in S4.

Federal Motor Vehicle Safety Standard – Wikipedia

Measure and record the length of belt between points A and B along the longitudinal centerline of the webbing for the lap belt or lap belt portion of the seat belt assembly while the pre-load is being applied. Manufactured on or after Britax Roadster December 1, If a Type 2 seat belt assembly installed in compliance with this requirement incorporates any webbing tension-relieving devicethe vehicle owner’s manual shall include the information specified in S7.

If the child restraint or dummy contacts the vehicle interior, move the seat rearward to the next detent that provides clearance, or if the seat is a power seat, using only the control that primarily moves the seat fore and aft, move the seat rearward while assuring that there is a maximum of 5 mm 0.

The means for providing the required visibility may be adjustable manually or automatically, except that the telltales may not be adjustable under any driving conditions to a level that they become invisible or not recognizable to the driver rregulation right front passenger.

When measuring neck injury, each of the following injury criteria shall be met. The midsagittal plane of the driver and the passenger dummy shall be vertical and shall coincide with the longitudinal centerline of the bucket seat.

  EL MISTERIO DE LA CALLE DE LAS GLICINAS PDF

Federal Motor Vehicle Safety Standard 208

Adjust each head restraint vertically so that this horizontal plane is aligned with the center of gravity CG of the dummy head. Complete any procedures recommended in the vehicle owner’s manual, pursuant to S7.

Such vehicles may be excluded from all calculations of compliance with S4. A multipurpose passenger vehiclereyulationor bus is loaded to its unloaded vehicle weight plus pounds or its rated cargo and luggage capacity weight, whichever is less, secured in the load carrying area and distributed fmbss nearly as possible in proportion to its gross axle weight ratings, plus the weight of the necessary anthropomorphic test devices.

S24 Test procedure for S If it is not possible to position the dummy with the legs ergulation the prescribed position, rotate the legs forward until the dummy is resting on the seat with the feet positioned flat on the floor pan, and the back of the legs are in contact with the front of the seat cushion. If the seat belt assembly installed in compliance with this requirement incorporates any webbing tension-relieving devicethe vehicle owner’s manual shall include the information specified in S7.

By developing a robust record of the answers to these important questions, NHTSA expects to learn more about the progress of ADS and the ways in which the Agency can regulatino safe and efficient ADS testing and deployment for the benefit of individual consumers and the traveling public as a whole. Adjust the lap belt or lap belt portion of the seat belt fnvss pursuant to S7. Cinch the vehicle belts to secure the car bed.

The manufacturer shall also provide a written notice by registered mail to the first purchaser of the vehicle for purposes other than resale, within two weeks after purchase.

Graco ComfortSport September 25,