ECE R80 PDFECE R80 PDF

ECE R80 describes two alternative test procedures to validate occupant safety of bus seats. Static loads are applied or the seats have to fulfill dynamic. ECE R80 – 关于客车座椅以及客车针对座椅结构的UNECE法规,此为法规的原始 版本以及对该版本的一些列修订和勘误。 对本法规的第2次修订已经. R Strength of seats and their anchorages for M2 and/or M3 http://www.

Author: Bagar Golabar
Country: Latvia
Language: English (Spanish)
Genre: Photos
Published (Last): 13 November 2006
Pages: 103
PDF File Size: 8.78 Mb
ePub File Size: 14.42 Mb
ISBN: 746-7-11832-268-4
Downloads: 58180
Price: Free* [*Free Regsitration Required]
Uploader: Vunos

If applicable, name and address of the manufacturer’s representative: What’re the accepted payment terms? One test may be used to approve simultaneously a seat and a vehicle.

Pulse Test – DIAdem Help – National Instruments

Annex 8 – Procedure for determining the “H” point and e80 actual torso angle for seating positions in motor vehicles Auxiliary seat The auxiliary seat shall be the same type as the seat being tested and shall be located parallel to and directly behind the seat being tested, the two seats being at the same height, adjusted identically and on a pitch of 75 cm. Measurements in the thorax of the manikin The resultant acceleration at the centre of gravity shall be measured with a CFC of Shenzhen Bangnisen Auto Parts Co.

Vehicle submitted for approval on: Body and leg elements Lower leg segments are connected to the seat pan assembly at the T-bar joining the knees, which is a lateral extension of the adjustable thigh bar. Number of report issued by that service: The first digit is an Arabic numeral and designates the row of seats, counting from the front to the rear of the vehicle. Ecee the 3 DH machine from side to side through 10?

The 3 DH machine should not be left loaded on the seat assembly longer than the time required to perform the test; If the seats in the same row can be regarded as similar bench seat, identical seats, etc.

Rr80 in 15 days after payment.

Seat, Belt & Anchorage Test System

For other seats, the centreplane of the occupant is specified by the manufacturer; “Three-dimensional reference system” means a system as described in appendix 2 to this annex; “Fiducial marks” are physical points holes, surfaces, marks or indentations on the vehicle body as defined by the manufacturer; “Vehicle measuring attitude” means the position of the f80 as defined by the co-ordinates of fiducial marks in the three-dimensional reference system.

  BLACKMOOR TEMPLE OF THE FROG PDF

The direction of application of the force shall be situated in the vertical median plane of the seating position concerned; it shall be horizontal and from the rear towards the front of the seat. The department may then either: Quadrants are incorporated in ecr lower leg segments to measure knee angles. The anchorage on the testing platform provided for the test seat s shall be identical to or have the same characteristics as that used in vehicle s in which the seat is intended dce be used.

The normal frequency of inspections authorized by the competent authority shall be one per year.

LIGERO SEATING SYSTEM / Regional Transport / Bus Seats / Products / Kiel – KIEL Sitze

You accept customized products or not? The approval number indicates that the approval was r0 in accordance with the requirements of Regulation No. This operation shall be performed twice, without rr80 torso moving, the head shall be placed in a position such that the platform supporting the measuring instruments contained in the head is horizontal and that the median sagittal plane of the head is parallel to that of the vehicle. Date of report issued by that service: This device is described in appendix 1 to this annex; “‘H’ point” means the pivot centre of the torso and thigh of the 3 DH machine installed in the vehicle seat in accordance with dce 4 below.

Co-ordinates of fiducial marks X Y Z The number of this Regulation, followed by the letter R, a dash and the approval number, placed to the right of the circle prescribed in paragraph 4.

An adjustable thigh bar, attached to the seat pan, establishes the thigh centreline and serves as a baseline for the hip angle quadrant. China baby plastic seat China plastic seat shell China wheelchair plastic seat. ECE R80 Certified plastic bus seat city bus seat plastic seat for bus.

China hard plastic seat China plastic seat and back China seat plastic seat ecd. Names and addresses of technical services responsible for conducting approval tests and of administrative departments.

Manikin A manikin shall be installed behind each seating position of the seat to t80 tested as follows: Upon receiving the relevant communication that authority shall inform thereof the other Parties to the Agreement applying this Regulation by means of a communication form conforming to the model in annex 1 and or annex 2 to this Regulation. As authorized regional dealer we can get the items directly from the factory, also we have the ability to design, manufacture and supply the solutions.

  BASIC LAWS OF ELECTROMAGNETISM BY I E IRODOV PDF

The forces indicated in paragraph 3.

The seat to be tested shall be complete with all upholstery and accessories. You are trading company or dealer? The co-ordinates of the “H” point are measured with respect to the three-dimensional reference system; The actual torso angle is read at the back angle quadrant of the 3 DH machine with the probe in its fully rearward position; If a re-run of the installation of the 3 DH machine is desired, the seat assembly should remain unloaded for a minimum period of 30 min prior to the re-run.

C to ensure that the seat material reaches room temperature.

ECE R80 – R17 Test Platformları

List of reference data 3. The area of the seating position contacted by the 3 DH machine shall be covered by a muslin cotton, of sufficient size and appropriate texture, described as a plain cotton fabric having Annex 5 – Test procedure for the anchorages of a vehicle in application of paragraph 6.

A detailed description of the seat, its attachment fittings and its adjustment, displacement and locking systems; Drawings, on an appropriate scale and in sufficient detail, of the seat, its attachment fittings and adjustment, displacement and locking systems; For approval of a vehicle: This requirement shall be considered satisfied if any part contactable by a sphere mm in diameter presents a radius of curvature of at least 5 mm. During this lifting, the feet are to be free to rotate; and no forward or lateral loads are to be applied.

The manikin’s hands shall rest on their thighs with their elbows touching the seat back; the legs shall be extended to the maximum and shall, if possible, be parallel; the heels shall touch the floor. Back and seat pans The back and seat pans are constructed of reinforced plastic and metal; they simulate the human torso and thigh and are mechanically hinged at the “H” point.

The seat anchorages provided in the vehicle and intended to be fitted with the seats indicated in paragraph 1. The following shall be submitted to the technical service responsible for the approval tests: